Small white bathroom with a pedestal sink, toilet and black-and-white checkered floor

Heated towel racks, in the finish the rest of the bathroom is in.

A heated towel rack is the one bathroom fixture nobody regrets and almost everybody adds too late. Late means a surface-mounted cord down a tiled wall, because the decision arrived after the electrical rough-in. Crateworks supplies ladder-style racks in the same finish families as the taps and the hardware, and flags the rough-in on the brief so the circuit is in the wall before the tile goes on.

Updated

Hardwired or plug-in

Hardwired is the right answer in new construction and any gut renovation. The supply comes out of the wall behind the rail, nothing is visible, and it can run off a timer or a switch with the rest of the bathroom. It has to be roughed in before the wall closes.

Plug-in is the retrofit answer. It needs a receptacle within reach of the cord, positioned so the cord does not run across tile, and in a bathroom that receptacle has to be ground-fault protected. Easier to install, harder to make look deliberate.

Either way it is a bathroom electrical fixture, which means damp location rating, clearance from the tub and shower, and a circuit your electrician has signed off. Flag it on the brief and it goes on the electrical plan rather than into a wall that is already closed.

The certification question, answered straight

A heated towel rail is electrical equipment before it is a bathroom accessory, and that is where imported product most often fails. In Canada the rule is that the product carries an official Canadian certification mark from a recognised certification or evaluation agency. Ontario states it plainly in Rule 2-024 of its electrical safety code, and the recognised list runs to CSA, ULC, Intertek and a handful of others. A certification held only in another country does not satisfy that on its own, and a European CE mark satisfies nothing here.

Field evaluation exists as a rescue path when a unit arrives unlabelled, but it is designed for one-off and low-volume equipment rather than for a production line, so it is not a way to import uncertified fixtures at scale. Anyone telling you otherwise is describing a problem, not a solution.

Crateworks does not ship an electrical fixture into a jurisdiction where it does not hold a listing valid there. That is a policy, not a marketing line, and it is the reason this page does not claim a listing we would have to walk back. Ask about a specific unit and you get its actual status, including where the answer is that we cannot supply it yet.

One more thing worth confirming on any imported rail: that it is built for 120 volt North American supply rather than 220 volt. It is a question that costs nothing to ask and a great deal to discover at commissioning.

Sizing and placement

Mount it where a wet towel will actually be hung, which is usually beside the shower door rather than on the far wall where the drawing put it. Allow the manufacturer clearance above and below so air moves, since a rail packed tight against a vanity heats the cabinet rather than the towel.

Bar count decides capacity. A six-bar rail dries one bath sheet, a ten or twelve-bar rail handles a family bathroom. In a primary suite, size for two large towels hung open rather than folded, because folded towels dry from the outside in and mostly do not.

For the rest of the room

Guides


More in bath & plumbing

Common questions

Ask about the specific unit and you get the specific answer, including no. Canada requires an official Canadian certification mark from a recognised agency such as CSA, ULC, or Intertek, which a certification held only in another country does not provide on its own. We do not ship an electrical fixture into a jurisdiction where it does not hold a valid listing, and we would rather lose the line item than have an inspector find it.
Hardwired for new construction or a gut renovation, because the supply hides in the wall and it can run on a timer. Plug-in for a retrofit where opening the wall is not on the table, accepting that the cord will be visible and that the receptacle has to be ground-fault protected. The decision belongs at electrical rough-in, not at fit-out.
Before the electrical rough-in, which is earlier than most people think. A hardwired rail needs a circuit and a supply point behind it at a specific height. Added after the tile is on, the honest options are a surface cord or demolition.
Count towels, not wall space. Six bars dries one bath sheet, ten to twelve handles a family bathroom. Hang towels open rather than folded, since folded ones dry from the outside in. In a primary suite size for two large towels hung flat.
Not meaningfully. A towel rail is sized to dry towels, not to be a heat source, and it should not be specified as a substitute for bathroom heating. If the room needs heat, that is a separate line on the mechanical plan.
That is the reason to buy it with the schedule rather than separately. Rails are supplied in the same finish families as the taps and the bath hardware, so it reads as part of the bathroom instead of an appliance bolted to the wall.

Send the bathroom electrical plan.

Rail count, hardwired or plug-in, finish family, and the install jurisdiction. It comes back with the listing status per unit before you commit.